ONLINE TRUCK SEAT COVERS

CAR SEAT COVER INSTALLATION LOCATIONS

Our True-Fit® and H2Out® custom seat covers are created to perfectly fit the front and back seats of your car. 

HOW DO WE INSTALL YOUR SEAT COVERS?

PLEASE NOTE: If Headrests Are Adjustable, Remove By Pressing Button On Side. Some Cars, vehicles & Trucks (Chevy, Dodge, Ford & GMC) Have A Tiny Hole On The Plastic Cap. Insert Paper Clip Into Hole In Order To Release Headrest. Refer To Owner’s Manuals For More Details On How To Remove Headrests If Necessary. Study Seats And Seat Covers For Any Openings To Help Determine Driver And Passenger Seats. Note: Identical Rectangle Openings On One Side Of Each Seat Cover May Be The Airbag Opening, Thus These Opening Goes Toward The Outboard (Door Side) Of Each Seat. Car upholstery installation shops.

ONE-PIECE SEAT COVERS

1. 1. Slide Seat Covers Over Backrest Firmly But Gently Pulling Down Evenly On Both Sides. Because Of The Custom-Fit (Snug) Design Of These Seat Covers, Careful Manipulation May Be Necessary To Conform To Seats. You May Loosen Elastic Bungee Cord At The Bottom If Additional Slack Is Needed – But Be Careful: First Tie A Knot At The End Of The Cord To Secure It.
   2. Once Seat Cover Is Installed Over Backrest, Tilt The Backrest Forward – Pulling The Elastic Loops (From Inside Of The Cover) Through The Crack Between The Upper Backrest And Lower Seat Section And Hook Under Seat Cushion.
   3. Return Backrest To Its Vertical Position. Pull The Bottom Section Of The Seat Cover Around Seat Cushion While Aligning All Openings For Knobs Or Levers. Pull The Bungee Cord Tightly To Assure Proper Fit, Tie And Tuck Under Seat And/Or Close All Applicable Velcro Openings. Do Not Cut Off Excess Bungee As This Slack Will Be Necessary When Removing For Wash. When Applicable, Replace Headrests And Carefully Pull Headrest Covers Over Headrests And/Or Armrests.

TWO-PIECE SEAT COVERS

1. 1. Slide Seat Covers Over Backrest Firmly But Gently Pulling Down Evenly On Both Sides Then Wrap The Bottom Front Under The Seat (Towards The Back) And Attach To Rear Velcro. Because Of The Custom-Fit (Snug) Design Of These Seat Covers, Careful Manipulation May Be Necessary To Conform To Seats.
   2. Slip The Bottom Seat Cushion Cover Around The Seat Cushion While Aligning All Openings. Pull An. Y Straps Through To Back And Tie Bungee Cords Tightly.
   3. Tuck Any Excess Bungee Cord Inside Cover But Do Not Cut As This Slack Is Necessary When Removing For Wash. Custom Interior Auto Upholstery.

Michigan

• Detroit
• Flint

Montana

• Kalispell

Nevada

• Las Vegas
• Reno

North Dakota

• Fargo

North Carolina

• Wilmington
• Raleigh
• Charlotte
• Fayetteville

South Carolina

• Charleston
• Columbia
• Lexington
• Myrtle Beach
• Greer

Louisiana

• Shreveport
• Baton Rouge
• New Orleans

Washington

• Seattle
• Lynnwood
• Spokane

Oregon

• Beaverton
• Portland

Colorado

• Denver

Oklahoma

• Oklahoma City
• Tulsa

Ohio

• Columbus

Nebraska

• Omaha

Wisconsin

• Madison
• Milwaukee

Kansas

• Wichita

Custom Car Seat Cover Installation by Supreme Seat Covers. Supreme Seat Savers has custom seat cover options for most cars, vehicles, and trucks like Ford, Chevrolet, Jeep, Dodge and Chrysler, and more. Vehicle upholstery installation shops.